Iflight Chimera7 Pro HI) BNF DJI air unit 6S (TBS) 1250KV

• NO RX (DJI BNF)                                                                                     Introducing what has been requested for too long already! A super-efficient iFlight 7inch Long-Range bird that can go where you couldn't go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want! A super stiff frame for minimum resonance and XING2 2809 motors for maximum 7inch prop control. Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising. But whatever style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S 2.500mAh above. 
• GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behavior; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts are included to cover you and your antenna dead-ends just in case. GoPro universal TPU bottom stand included; fits your original GoPro bracket and our TPU GoPro protectors (additional).
  

Main Changelog from Chimera7 to Chimera7 Pro:

• SucceX-D F7 V2.2 Stack (F7+50A ESC) upgraded to BLITZ F722 Stack (F7 V1.1 + 55A 4in1 ESC)
• New Lightweight Side Panels Design - Keep Your Rig Clean
  
• XING 2806.5 upgraded to XING2 2809 1250KV
• 7-inch frame upgraded to 7.5inch
  

HIGHLIGHTS:

• Battery voltage LED status light (illuminated IF logo on the bottom)
• 360° TPU protection, DJI cam protection and antenna mounts
• GoPro TPU bottom stand (GoPro protector not included)
• Lightweight Side Panels Design - Keep Your Rig Clean
• No props in view (DJI Air unit record in 1080p/60fps)
• XING2 2809 1250KV efficient wide stator motors
• GPS pre-installed for more safety at a distance
• 6mm rigid arm design for more stiffness
• Top- and bottom battery mount option
  

PRE-TUNED & PRE-SETUP:

• Is this your first BNF or are you just starting through with FPV? This article might probably help: General Guide // iFlight BNF
  
• Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!
• To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"
• Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
• Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"
• GPS Rescue is OFF by default to prevent unwanted or unexpected drone behavior.
• Please check our linked article on"GPS Rescue Mode // Setup"
  

Specifications:

• Weight: 695g (without battery and GoPro mount)
  
• Total Dimensions: 258*200mm (body dimension)
• Bottom to Top Distance: 20-29mm
• Arm Thickness: 6mm
• Upper(middle) Plate Thickness: 3mm
• Bottom Plate Thickness: 3mm
• Camera Plate Thickness: 3mm
• Top Plate Thickness: 2mm
  
• Geometry:  DC (DeadCat)
• HQ 7.5X3.7X3 Propellers
  
• XING2 2809 1250KV
• FC // BLITZ F722
• ESC // BLITZ E55 4-IN-1 2-6S ESC

ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC)：

BLITZ F722 Flight Controller

• Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
• Smartaudio / IRC Tramp VTX protocol supported
• Firmware target: IFLIGHT_BLITZ_F722
• Motor outputs: 4x (SH1.0 connector)
• Flash: 32MB (Blackbox flash)
• I2C serial: SDA / SLA pads
• Dimensions: 36.5*35 mm
• Barometer: DPS310
• OSD Chip: AT7456E
• LED controller: Yes
• MCU: STM32 F722
• Beeper pad: Yes
• Gyro: BMI270
• Weight: 7.8g
• UARTS: 6
  

ESC // BLITZ E55 4-IN-1 2-6S 55A ESC

• Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
  
• Mounting Holes: 30.5*30.5mm/Φ4mm
  
• Target:   IFLIGHT_BLITZ_G2
  
• Supports 2-6S Lipo input
  
• Current sensor: Yes
  
• Constant: 55 Amps 
  
• Current rate: 200
  
• Burst: 65 Amps
  
• Weight: 15.3g
  
• MCU： G071
  
• BEC: No
  

Chimera7 Pro HD BNF Included Components and Parts

• 4 x HQ 7.5X3.7X3 CW propeller + 4 x  HQ 7.5X3.7X3 CCW (Color may vary)
• 2 x Albatross LHCP 5.8GHz SMA FPV Antenna
• 2 x iFlight Lipo Strap 20*250mm (Black)
• 1 x Pre-built and Tested Chimera7 Pro
• 1 x DJI FPV Air Unit Module + Camera

Note:

• All iFlight BNFs are tested before shipment to guarantee the highest quality. 
• If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.
  
• iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be directly reported to www.caddxfpv.com/pages/contact-us or www.dji.com